亚洲欧洲日韩国产精品视频,久久久久久久爽少妇毛片,熟妇老女人的诱惑av

關于防火板的起泡問題？

來源：http://www.gz-moutai.com/ 日期：2021-06-23 發布人：admin

防火板起泡原因可根據挑破起泡處后出現的材質判斷：

The cause of blistering can be judged according to the material after the blistering place is broken

1.起泡處挑破后現牛皮紙底板，可判斷為防火板質量差，需購買高質量防火板

1. After the blister is broken, the kraft paper bottom board is found. It can be judged that the quality of the fireproof board is poor, so it is necessary to buy high-quality fireproof board

2.起泡處挑破后現基材，原因為施工不成熟，以下為導致防火板起泡的施工原因、避免方法、和解決方法。

2. The base material is found after the blistering place is broken. The reason is that the construction is not mature. The following are the construction reasons, avoidance methods and solutions of blistering of fireproof board.

防火板起泡的施工原因：

The reasons for the blistering of fireproof board are as follows

1.施工時施壓不夠，不均勻

1. Insufficient and uneven pressure during construction

2.膠水局部未干就貼合：

2. The glue is not dry on the part

a、晾置時間不夠，膠水未干；

a. The drying time is not enough and the glue is not dry;

b、施工環境濕氣過大，膠水沒干透，出現假干現象，導致粘接不牢；

b. Too much moisture in the construction environment, the glue did not dry thoroughly, resulting in false dry phenomenon, resulting in poor bonding;

c、板材潮濕，粘不牢；

c. The board is wet and not firm;
富美家防火板

d、膠水涂刷局部過多，干不了；

d. Too much glue can't dry;

3.膠水局部缺膠。

3. The glue is partially lacking.

防火板起泡的避免方法：

Methods to avoid blistering of fireproof board:

1.均勻用力施壓至貼合。

1. Press evenly to fit.

2.a、適當延長晾置時間：

2. A. extend the airing time appropriately

b、通風干燥、用太陽燈照射或更換場所；

b. Ventilate and dry, irradiate with sun lamp or change place;

c、粘物晾干或烘干后再使用；

c. The stickies can be used after drying or drying;

d、均勻、一次性刮膠.

d. Uniform, disposable scraping

3.均勻刮膠，不要缺膠.

3. Scrape the glue evenly without missing glue

防火板起泡的解決方法：

Solution to blistering of fire-proof board:

在干燥的環境下，于防火板上放置毛巾，用電熨斗燙平。

In a dry environment, place a towel on the fireproof board and iron it with an electric iron.

上一篇：富美家?金麗?金屬耐火板的自然魔法 下一篇：選擇竹木式快裝板的原因？

分類導航

產品中心

聯系我們

成功案例

聯系我們

新聞動態

聯系我們

熱門產品推薦

相關新聞